Plumber Geelong 17 June
Posted by Admin on June 17, 2014
Archive for blog
Have you run your bath water only to realise its ice cold? Have you jumped in the shower and been sprayed by cold water? If so, chances are you have a problem with your homes hot water system . Don’t stress, there are a few basic things you can try yourself prior to calling a plumber. If you have a natural or propane gas water system, chances are the pilot has gone out. The pilot is a small flame that ignites the gas burner on your system. When it goes out, first try relighting it, following the directions on the label, which is often on the front of the system. If the pilot doesn’t relight, or if it goes out right after lighting, by far the most common cause is a broken thermocouple. The good news: you can usually replace a thermocouple for minimal cost and in less than an hour from a local hardware. You’ll get your hot water going without waiting for a pro to show up and save a few dollars!
To replace the thermocouple, be sure to turn off the shutoff valve in the gas line; that is, one quarter turn so that the handle is at a right angle to the pipe. Since working room is tight around the burner, we recommend that you simply unscrew the three nuts at the control valve and pull out the entire burner assembly unit. You’ll see either a slot or clips that hold it in its place. Then either unscrew the thermocouple end or pull it out (depending on the water heater) and take it with you to hardware store to find a match. Position it exactly the same way as the old one. The pilot flame should wrap around the thermocouple bulb.
To reattach the three lines to the gas valve, thread the nuts into place with your fingers and hand-tighten them properly. Then snug them up with a quarter to half revolution with a wrench. The metals are soft, so don’t over tighten as they will break.
Be sure to test for gas leaks. You must have the pilot lit and the burner on for this test so that gas is flowing through the large tube on the system. Reopen the shutoff valve, relight the pilot, then turn the control valve to the “on” position. When the gas burner is on, use a 50/50 dish soap/water mix to test the screw joints for air bubbles that indicate leaks.
Tags: 24 hour plumber geelong , emergency plumber geelong , geelong plumber , plumber geelong
Posted in: blog
Leave a Comment (0) →
Tags: 24 hour plumber geelong , emergency plumber geelong , geelong plumber , plumber geelong
Posted in: blog
Leave a Comment (0) →Bathroom Plumbing
Kitchen Plumbing
Tags: 24 hour plumber geelong , blocked drain geelong , emergency plumber geelong , geelong plumber , plumber geelong
Posted in: blog
Leave a Comment (0) →The common and general plumbing mistake involves the wrong selection of pipes when repairing leaks in your house. This is both in terms of the size & the type of the pipe that is being used. The pipes may therefore fail to fit into each other, as you need. Using too much force when connecting 2 pipes together or forcing the connectors may break the pipes or the pipe connectors. Further leaks may develop in the pipes and they may burst when pressure builds up in the pipe. Corrosion may also occur if you get the pipe type wrong. Professional plumbers know when to use galvanized pipes and when to use the correct copper pipes. Connecting the 2 will lead to corrosion which will require regular replacement of the pipes.
Improvising makeshift tools and equipment in place of what the professional plumber uses is another regular mis happening. For eg, many people use marbles or ball bearings in place of a real level when installing or repairing bathroom fixtures. A ball bearing or marble may not work when checking the level and this could force you into unnecessary common reworks. Getting the level wrong when installing the toilet could also lead to slow flow of sewer or even backups in the plumbing pipes. Using the correct tools for a given task will not only save you time but will also make sure that the pipes do not crack as you are fitting them.
You need to have a good design of where the sewer pipes are to be placed. This is especially the case when carrying out plumbing works in the upper floors of a building or apartment blocks. An odd DIY plumbing mistake involves routing the pipes in the wrong places so that they interfere with occupants of the higher floors of the building. Imagine a situation where you are always woken up by the sound of toilet flushing from the floors above. A common practice by professional plumbers involves designing & planning the drainage network before the implementation.
The last DIY plumbing mistake in the list is failure to turn off the water stopcock before attempting any type of repairs. This is always the first thing that a professional plumber will do even for the tiniest plumbing tasks at. Doing so prevents flooding, which often causes damage to common household items. It will also take you added time to drain the water from the bedroom.
Trying to fix a small problem on your own and getting it wrong could create a major problem. Hiring an emergency plumber to rectify the bigger problem will cost you more money. You should therefore take your time when doing your own plumbing work to avoid such mistakes or call a professional plumber in case you are not sure how to fix the problem
Tags: 24 hour plumber geelong , blocked drain geelong , emergency plumber geelong , geelong plumber , plumber geelong
Posted in: blog
Leave a Comment (0) →
Tags: 24 hour plumber geelong , emergency plumber geelong , geelong plumber , plumber geelong
Posted in: blog
Leave a Comment (0) →If your pipes are noisy that they sound like squeaking or hammering, you can easily solve this problem. You can anchor exposed pipes to get rid of noises. Call a plumber to help with pipes that need you to cut a hole in a wall, ceiling or floor.
Many plumbers will request a deposit before commencing a major plumbing repair. On smaller jobs, they will request payments at the end of the jobs.
If your home operates on well water and you notice pink or orange stains in your bath tub and other fixtures, this is due to iron in the water. You should purchase a water softener, or ask a local plumber to make a visit to your residence & resolve the issue for you.
Putting a cup of any kind of baking soda followed with a cup of white vinegar into your drain each month will keep your drain running well. This should cause a chemical reaction to occur and you should plug the drain. Wait a while, and then use boiling water to flush the drain. Although this is useful for clearing away simple clogs made of hair and soap debris, it will not work for the more serious blockages.
Water that drains back into your dishwasher is likely due to a damaged sink hook up. The hose going from the dishwasher to the sink needs to angle upwards before going back down hill to prevent water from both being mixed.
Do not use your toilet like a rubbish bin to minimize potential problems. If you flush improper items such as disposable diapers, facial tissue, cotton balls, paper toweling, tampons or sanitary napkins down the toilet, you will surely have problems with blockages. Also, try to use the smallest amount of toilet paper you can.
Keep your dryer’s lint trap clean. By doing this simple task, you can prevent a great deal of trouble. This includes prevention of fires. See to it that you look at the lint trap and find out if it has tears or holes in it that could cause lint to go inside your pipes, which could lead to clogs or other plumbing problems in the future.
Keep your bathtub in good shape by using a cup of baking soda & a cup of vinegar down its drain on a regular basis. Use the technique above to help you. Doing this will help rid your pipes of disgusting soap scum and clogs.
Now you have the understanding of plumbing tips that you can apply to fix your plumbing issues in your home. The above tips were constructed to add to your plumbing skills, as you are never done learning or improving them.
Tags: blocked drain geelong , emergency plumber geelong , geelong plumber , plumber geelong
Posted in: blog
Leave a Comment (0) →
Tags: blocked drain geelong , geelong plumber , plumber geelong
Posted in: blog
Leave a Comment (0) →If your pipes make squeaking and hammering noises, it may be easy to fix. Exposed pipes need to be anchored when they are installed. If pipes are located in the floor, ceiling or walls, you might want to have a professional help you complete the job.
Make sure the plumber gives you an estimate before he commences. You may be required to put some money down before a job is started as a deposit. Never pay the total cost until you know the job has been completed correctly. This will help to ensure that the plumber is concerned about quality of the work.
Don’t use tough chemicals such as toilet tablets in your toilet. Many kinds of toilet tablets might break down obnoxious smells in your toilet, but they might break down the rubber parts.
If you are unable to fix a clogged toilet with a plunger, try pouring a small bucket of water into the bowl from about waist level if the level of water in the bowl has lowered. You can repeat this process again if the water in the toilet bowl lowers again.
Take quality into account when it comes to replacing a showerhead. It is common to think it is fine to buy a showerhead that is the cheapest. The big issue with this is they aren’t sturdy and they tend to break a lot easier.
You need to use the information that has been provided so that you can make the best decision when it comes to alleviating your plumbing issues in your home or office. Getting a plumber for the job that is effective, affordable and has a proven track record can end up being more difficult than fixing the issues itself. Take these tips to heart, and you’ll be better for it down the line.
Tags: emergency plumber geelong , geelong plumber , plumber geelong
Posted in: blog
Leave a Comment (0) →